Sell a Surplus Water-Cooled Chiller in St. Matthews, SC
We buy used water-cooled chiller equipment in St. Matthews and handle the agreed disconnect, rigging, and freight.
We buy chillers. We don’t sell them.
Your chiller.
Our logistics.
Have a surplus or decommissioned chiller? We’re the buyer—here to make moving it straightforward.
From a single unit to equipment from a larger facility, tell us what you have. We buy industrial and commercial chillers across South Carolina and coordinate the work to get them moved.
See how it works
All types & sizes
Air-cooled or water-cooled, centrifugal, screw or scroll. Tell us what you have.
We handle the logistics
We coordinate rigging, refrigerant recovery, loading and freight for the equipment we buy.
Made for sellers
Send the details and nameplate photos to start a conversation about your chiller.
Three steps.
One less chiller.
- 01
Send the details
Share what you know, along with photos of the unit and nameplate.
- 02
Get a quote
We’ll review your equipment and discuss an offer with you.
- 03
Leave the logistics to us
We coordinate removal and freight for the chillers we purchase.
Turn an incomplete inventory into a useful offer discussion
If you have a surplus water-cooled chiller in St. Matthews, South Carolina, you do not need a complete equipment file before asking South Carolina Chiller Buyers to consider it. Start with what you can identify: the chiller’s location, visible nameplate information, approximate capacity if known, and whether the unit is installed or already disconnected. The buyer considers chillers of all tonnages, including units below 20 tons; 20 to 2,000+ tons is a common range, not a minimum or limit.
South Carolina Chiller Buyers is a direct buyer, not a seller of replacement equipment. An initial conversation can clarify what is known, what still needs confirmation, and whether the unit may fit a purchase. A missing manual or uncertain model number does not by itself prevent you from requesting an offer.
Describe the two water circuits separately
A water-cooled chiller normally interfaces with a chilled-water loop and a condenser-water loop. They serve different purposes, so identify each set of connections as clearly as you can. If labels or drawings are available, note which piping belongs to each loop. If you are unsure, say so rather than guessing from pipe size or location.
Also clarify what is included in a possible sale. The cooling tower, pumps, controls, and nearby piping may be part of the surplus equipment, or they may remain with the property. That distinction affects the purchase discussion and the removal scope. For example, if a tower serves more than one system, it may need to stay while the chiller is removed; if it is dedicated and also surplus, you can ask whether it should be considered separately. These are possibilities to confirm, not assumptions about a particular site.
Use photos to show boundaries and access
When records are incomplete, photographs can help explain the installation without requiring you to operate or dismantle anything. Useful views include the chiller’s nameplate, the overall machine, visible valves and insulation, pipe runs at the unit, and the route from the machinery room to the exit. A wider view can show whether equipment or building features may affect access. Do not remove covers or enter unsafe areas to obtain a picture.
For water-cooled chiller removal, the disconnection plan must distinguish the chiller from shared piping and any cooling equipment that will remain in use. Photos of connections and the machinery-room exit can help establish where the removal boundary might be. If the line ownership is unclear, mark it as unknown for discussion rather than treating a shared system as part of the sale.
Separate capacity from the challenge of moving the unit
Capacity, usually stated in tons, describes cooling capability; it does not tell you the chiller’s transport weight or whether it will pass through a particular doorway. The physical machine, attached components, access route, and rigging conditions all matter to removal planning. If you have a weight listed on a data sheet, share it as a reference, but do not infer weight from tonnage alone.
A chiller that appears modest in capacity could still present a difficult move if it sits below grade or has a restricted exit. Conversely, a larger machine may have a workable route, subject to review. Share known constraints, such as stairs, low overhead clearance, narrow doors, or limited staging space, without attempting to move or prepare the equipment yourself.
What to include when details are missing
A short inventory can be enough to begin. Gather only information you can access safely and lawfully; the authorized owner or site representative should confirm permission and coordinate access.
- Make, model, serial number, and nameplate photos, if visible
- Approximate capacity and operating status, if known
- Whether the chilled-water and condenser-water connections are identified
- Which pumps, tower, controls, or piping may be included or retained
- Photos of valves, insulation, pipe runs, the machine room, and exit route
- Any known access restrictions or uncertainty about shared systems
You do not need to test, start, repair, or prepare the unit to request an offer. Do not energize, open, drain, vent, cut, or dismantle equipment to complete the inventory. If operating history or refrigerant details are unavailable, say so; South Carolina Chiller Buyers considers all brands and refrigerants.
Understand what follows an agreed purchase
After a purchase is agreed, the buyer handles the disconnects, necessary refrigerant recovery through appropriately qualified personnel, crane and rigging, loading, hauling, and freight. Freight is covered. The seller does not need to hire a carrier or ship the chiller. Site authorization and coordination still matter: the owner or authorized representative must permit the work and arrange access for the agreed removal.
Refrigerant and process fluid are not the same thing. Refrigerant is contained in the chiller’s refrigeration circuit; water or another process fluid may circulate through the building loops. Do not release either substance or attempt to empty the system. The removal plan should identify the equipment and connections so qualified personnel can handle required work appropriately.
Set expectations around price and timing
An offer and removal schedule depend on the equipment details, access, included components, and the terms agreed with the buyer. Do not rely on a tonnage figure alone to predict price or a removal date. For instance, if a model is unknown but clear photos show the machine and access route, the buyer may be able to identify what additional information is needed; if shared piping or included equipment remains unresolved, that scope may need clarification first.
Payment is upfront under the agreed purchase. Provide a candid account of what is known and leave uncertain points open for review. That gives both sides a practical basis to discuss your water-cooled chiller in St. Matthews without asking you to perform unsafe work or fill gaps with guesses.
Ready to move
your chiller?
Tell us what you know. If you’re unsure of a detail, leave it blank. Nameplate photos are a great place to start.
Request a quote.
Fill out what you can and we’ll be in touch.